Simple long yoga socks on a sock loom

bild (10)bild (9)bild (11)bild (13)


Sock loom
Sock yarn (i used drops delight 191 yds per skein and i used 2 skeins )
Sewing needle to weave in ends
Measure tape to measure your foot

I made my socks on Kiss fixed 1 fine gauge loom. If you want to use same stitches as I do you need to be able to cast on amount of pegs dividable by 4 (I use k2, p2 as cuff).  My gauge swatch gave me 8 pegs and 16 rows for an inch. You need to make your own swatch, cast on 29 pegs and knit for 30 rows, bind off take off the loom (don’t cut the yarn), then pin it down with pins and measure how many stitches and rows your gauge is. You can then rip it out after you take note. After this you will take your tape measure and measure around the fattest part of your foot, in my case this is just above my toes. As I have big feet for me this measured 8”. Simple math will tell you that 8 pegs per inch x 8 inches needed will yield 64 pegs cast on. If your calculation give you an amount not dividable by 4 I would suggest you size down as yarn is usually pretty stretchy. I will be wearing mine with socks under as we seem to be having some kind of arctic winter going on so I will start mine with 64 pegs.

Socks length is: 4,75 inches till heel opening, and 3,75 inches from heel to toe. Again my foot size is 7,5. You take a measure of your foot from end of the heel up to the toes, then multiply this with how many rows you gor per inch from your swatch to decide the length over the foot itself, you can do same for length above the ankle if you want shorter yoga socks. Now that you have your amount of pegs to cast on and amout of rows to knit noted down lets get started.

Ewrap cast on 64 pegs (or amount you calculated from your swatch).

Row 1- 10: knit 2, purl 2* repeat till end.
Row 10 – 66 (or the rows you calculated you want the length above the ankle to be): knit all

Row 67 – 77: knit first half of your pegs (for me its peg 1 – 32), k2, p2 other half of the pegs.

Row 78: Knit first half of your pegs (peg 1 – 32), cast of other half of your pegs. (this creates the opening over the heel).
Row 79: Knit first half of your pegs again (peg 1 – 32 in my case), ewap cast on other half (pegs 33 – 64 in my case).
Row 80 – 90: Repeat rows 67 – 77.
Row 91 – 136: Knit all  pegs.
Row 137: I want my socks to be a bit tighter around the toe so on this row i decreased 4 pegs, 1 on each side of the slider then i moved the sliders one peg in. This has left me with 60 pegs.

Row 138 – 141: knit all pegs.
Rows 142 – 152: k2, p2* repeat till end of row.

Cast off, weave in ends and enjoy.

If you do a swatch and adapt the pattern after your own foot these socks can be made both on All-in-one loom and MS loom. If i calculate from a swatch with worsted weight yarn and all in one loom i get 44 pegs cast on and 50 rows till heel and 25 rows over the foot.

bild (12) bild (15)  bild (14)


Fast and easy leg warmers on all-in one loom

These make for a quick and easy last minute gift or just a cool accessory for yourself.
Gauge I made mine in is 22 pegs and 42 rows for 4″ x4″ (10×10) cm
Size: adult length: 35cm (14,5″), to suit an m to l size.
What you need is:

  • all in one loom or ms loom
  • Two skeins of yarn (or more depending on yarn you use) in example I used 246 yards of drops Nepal, a worsted weight yarn 75% wool and 25% alpaca + scrap yarn for stripes.
  • looming pick
  • a needle to weave in ends

How to get started: if you are using ms loom kit it needs to be set up with small pegs in every hole. Pegs need to be evenly divided by 4 if you are doin k2, p2 cuff which I find prettiest. If you prefer k1, p1 then an amount dividable by 2 is recommended.

Cast on 52 pegs (if you are using ms loom you can either cast on 48 or 56 pegs dependable on leg size.
Cuff: Row 1 – 15: *k2, p2* rep till end of row
Knit using knit stitch till your work measures 33cm (13,5″) from cast on edge.
Cuff end: repeat Cuff.
Bind off using regular bind off.

Tip: be creative. Use different colored yarns to achieve more playful effect or use different stitches to alternate this pattern. Example bellow uses one row of contrasting yarn every 8th row.






Easy cowl

Set up you loom as follows (yes again it’s Ms loom kit) 2 28-hole semi circle, 4 12-hole pieces and 2 6-hole pieces. Put big pegs in every other hole.
Materials: 2 skeins 50gr each of worsted weight yarn, loom pick, needle to weave in threads.
E-wrap cast on the loom. I got 58 pegs with this configuration.
Row1: knit
Row 2: purl
Row 3: knit
Row 4: purl
Row 5 – 46: knit
Row 47: purl
Row 48: knit
Row 49: purl
Row 50: knit
Bind off using super stretchy bind off. Weave in ends. For me the length was so if I want I can pull it over my nose so I folded down the start and en parts. Wear or give away and enjoy.

Superduper easy cowl on MS loom and weave kit

Cowl with flower

This cowl came about as it was extremly cold and I was knitting upp some things to give away to the homeless shelted we have here. Its nothing fancy but its easy and works up fast, and mostly came about as I dint have any thick yarn to make hats on kk loom. Lets get started:

Superduper easy cowl

You will need:

  • 2 skeins of 50gr worsted weight yarn (to be used and held as one strand)
  • 2 28-hole semi circle pieces, 4 12- hole straight pieces
  • Loom pick of your choice
  • Needle to weave in ends when you are done

Asseble the loom:

Put the 12-hole pieces togather 2 and 2 and attach 28 pieces to them, Using 1 large green peg, mark the start of your row, then place pink pegs in every other hole till you fill your loom (I ended up with 52 pegs placed).

The Cowl:

Cast on by ewrapping every peg, then ewrap them again and knit them off. I did this to get a stretchy end to it.

Knit in the round as following:
Row one: Knit (using regular flat stitch, you dont want it to be too tight)
Row two: Purl

Knit till you get your desired lenght. Mine seems to be at 50 rows as I am kitting up all the yawn in the darker skein. Bind off using super stretchy bind off. Weave in ends and enjoy!